Cartridge Warmer WX-4A with 4 Free Cartridges (Open Box)

Technical specifications:

Voltage : 110V 

Frequency: 50Hz/60Hz

Power: 200W

Capacity: 1pcs 100 ml

Max Temperature:100 °C

Nonadjustable temperature

Body material: ABS

Inner material: Aluminum

Warranty 1 year

It fits standard cartridges with the following measurements:

Height: 13.5 cm / 5.31 inch

Length: 5.5 cm /2.16 inch

Width: 2.25 cm / 0.88 inch

Wax Necessities WX-1I  Wax Cartridge Heater.

Ideal for use with all Wax Necessities soft wax cartridges, the WX-4A heater can hold 4 cartridges. On the exterior, the heater is molded in a highly resistant APSthermoplastic plastic resin, and aluminum is used for the inner construction.

To prolong the life and efficiency of the warmer, it is recommended a cartridge always be inserted into the heating chamber. Do not pour wax directly into the heating well.

To maintain the optimum condition of the heater, clean regularly. Your warmer has been tested before leaving the factory and is guaranteed against all manufacturing defects, under regular use, for 12 months from the date of purchase. If the heater fails to operate due to a defect in material or workmanship, we will repair or replace it with dated proof of purchase. The guarantee does not apply to damaged lids or heaters resulting from misuse or accident.

For warranties, contact: office@waxness.com.

INSTRUCTIONS FOR USE:

Remove the heater lid and place the wax cartridge/s directly into the heating chamber(We recommend Waxness cartridges).

Plug in the appliance. Light indicates power is on.

The indicator light will remain illuminated during operation time. Please allow 15-30 min, depending on the ambient temperature, until the wax is ready to use.

To ensure the wax has reached a suitable temperature and to avoid loss of profitable working time, it is recommended to plug in the warmer approximately half an hour before services begin.

Unplug and cover with the lid when not in use.

Caution: Locking the lid tightly may cause the lid to break. If the top adheres to the melting pot, pre-heat the warmer before lid removal to prevent the lid from cracking.

IMPORTANT SAFETY INSTRUCTIONS:

Read all instructions before using the heater!

When using electrical appliances, basic safety precautions should be followed.

WARNING:

THE HEATER AND WAX ARE GETTING HOT. ALWAYS TEST WAX ON A SMALL AREA OF SKIN BEFORE APPLICATION.

To reduce the risk of burns, fire, or Injury:

Always test the wax on a small area of the skin before application.

Do not touch the metallic surfaces of the warmer. The unit is hot when in use.

Use only on a flat, solid surface.

Do not plug in a unit where the power cord can be tripped on or where the cord hangs over the edge of the working table and can be pulled off.

Do not leave the unit on, unattended.

If the wax begins to smoke, unplug the unit immediately and have the electrician check.

Allow unit to cool before cleaning or storing.

Do not leave children unattended around the working heater. Use the unit only for the intended use as described in this booklet.

For best results, refer to Wax Necessities waxing instructions and instructions on the product package.

DANGER

To reduce the risk of electrocution: (which can result in Injuries 8. and death)

Unplug the heater immediately after use.

Please do not use it in bathrooms or on wet floors and surfaces.

lf unit falls into water, unplug it immediately. Do NOT reach Into the water.

Never operate the heater if it has a damaged power cord or plug, is not working correctly, or has been dropped or damaged.

Do not connect more than 3heaters on an extension cord.

For professional use only! 

• Open-box items are products returned by customers, inspected by our service center, confirmed to be in working order, and resold at a discounted price instead of being returned to the manufacturer.